Lantern 3D with Floral Decorations

 

Confection-colored details adorn four outer panels 

of this acorn-shaped vessel which encase the inner lantern hull. 

Bracket edge flanges add style at upper and lower angled edges. 

Thread wire or ribbon through center, add beads or tassel 

at bottom end, fashion hanging “eyelet” at top.

 Add interior magic by attaching a dangler of some kind, 

such as the “Egg 3D Hollow Ornament”, 

“Egg 3D Slice Form Ornament”, or 

two-sided “Cross Scroll Ornament” separate designs. 

Enhance holiday decor by hanging from chandelier, 

archway, high shelf or other appropriate location. 

Lantern measures approx. 8.25” tall x 4.25” wide when assembled. 

ASSEMBLY: 1. Identify and cut the shapes:

For the inner hull -

A hull two-wall sections (2)

B end collar reinforcement inserts (2)

Not shown: end [repairing] reinforcements (2)

For outer wall panels with decorations - 

C outer wall panels (4)

D decorations (4 sets), including:

left & right edge trim sections for upper, middle, lower

end brackets for top & bottom

stem rectangles for top & bottom

edge trim for center window opening, crown trim

double-tipped stems, blossoms & sepal overlays

with mid-side flourishes

three-hole "pop tabs" for left and right

2. Prepare the inner hull sections by bending back on

all perforation lines except the end collar shapes

at top and bottom.

3. Bend the top trapezoid panels back to align straight

side edge and overlap to match up with flange's

perforation line, and glue seam.

Repeat for bottom panels.

4. Bend the end stem rectangles to perpendicular,

overlap straight edge across adjacent tab and join.

Repeat for both ends.

5. Orient the two hull half sections to align and join

two side seams, plus . . .

. . . two upper angled seams and 

two lower angled seams, plus . . .

. . . and two upper & lower stems.

6. Bend the side walls of the reinforcement collar inserts

forward/up, apply glue to underside/outside of walls,

then insert backside-down into the square

opening. Slide down until . . .

. . . top wall edges match to hull top edges,

then apply thumb/fingertip pressure at each wall

until firmly in place.

7. Plan and devise a hanging method.

This may include narrow ribbon that can attach an interior

dangling object just at top, or from bottom with a tassel end,

two ends up through lantern interior -- including through

dangler -- then through top to form a hanging loop or

attach to a decorative hook.

NOTE: the ribbon or wire or other center mechanism can be

completed after the outer walls are in place.

However, it may be easier to manipulate and handle

before the walls are in place.

THE PROJECT MODEL USES A WIRE.

A) Form an open end loop/hook at one end of a length

of 16 gauge or equivalent wire which becomes bottom end,

then attach tassel or other bauble, then close loop.

B) Lay wire assembly across top of hull, with end loop

in place where it will stop at bottom stem hole opening.

Measure up wire to approx. position where you desire

bottom of selected dangler to be in finished assembly, 

and mark wire.

This image shows the slice form egg ornament as dangler,

held in place to help determine bottom measurement.

C) Form a cork screw "knot" just below the length

that has been marked. This change in the wire is

intended to stop the downward slide of the dangler egg

on the axis of the wire.

D) Insert the wire through bottom of lantern, turning

the wire so that the cork screw turns the punched hole,

while at the same time threading the egg's center tunnel

from bottom to top. Continue inserting the wire through

the top collar platform, then adjust as needed to help

the wire get to the final positioning.

E) At top, carefully use tool(s) to form a top hanging loop

and cutting away excess length.

8. As needed, position and glue in place 1-2 end

"repair" or reinforcement squares at bottom

and/or top collar platform, torqueing to allow the cut

split to open so it can be slipped around wire

or ribbon. Rotate the second (etc.) square so that

the split lands in a different direction from previous.

9. Add some slight back curl to each of the outer wall

shapes: turn panel face down on work surface,

then use a rod tool such as this 3/16" dowel

to press the shape in place while panel is drawn

up from under the tool.

10. Bend angle edge bracket flanges forward (valley)

and end "tabs" forward at top and bottom.

11. Add back curl to long decor shapes that will be

added on front of each panel, so that they will stay

adhered in place. 

Then position and glue in place.

Shown in these two frames is the window trim shape.

Add the "crown" accent at the top (narrow end)

where it hugs the top of window trim.

Add the end rectangles and brackets,

"pull tab" shapes where they can "register" at

tri-hole cut out positions.

Prepare the double-tipped stems by attaching

the corresponding small or large blossom overlays,

then the sepals at bottom of blossoms.

Position and attach in space between window trim

and pull tabs, with the center angle centered between

ends of pull tabs.

Position and attach the side "crown" accents centered

and offset on outside of stem center angle.

Finally, add the panel trim shapes at angle edges

upper and lower, and arch side trim shapes.

12. Curve the first completed outer wall panel around

the hull, then position and attach top stem end to stem panel

of inner hull. (Use a quick-grab glue such as Fabri Tack,

to attach ends securely.)

Once one end is securely in place, "wrap" or curve

the panel around the hull to position and attach

the other end in place, gently urging angled perf lines

to match up with the perforation corners of inner hull.

13. Repeat Step 12 to position the next panel,

position and attach first end . . .

. . . then second. As subsequent panels are positioned

and joined in place.

As previously noted, urge the ends into position

to duplicate the end stem panels.

NOTE that the angled bracket flanges

should line up and be glued together as part of the

"adding panel on" process.

14. Continue to add final two side panels in place,

aligning, adjusting, securing and attaching bracket

flanges as done before.

15. Finally, add finishing touches, including

for this wire-center version, a ribbon tied in knot

and bow. (For a ribbon center, consider adding

decorative or painted beads onto the ribbon at stem ends,

or other appropriate decorations of choice.

Here is the completed lantern with slice form

egg dangling inside.

Egg 3D Slice Form Ornament

 

Cut and bend along vertical centerline, join adjacent halves

 back-to-back (then join final half pairs to complete the circuit) 

to form oblong dimensional egg shape. 

Encase a hanging loop of twine or fine wire so that 

the egg form can dangle or hang, or use alternative 

slices which include a top-only hang loop. 

Hang from pegs, as part of decorative swag, 

under basket handle, 

on decorated seasonal wreath or egg tree. 

Sized to fit inside the “Lantern Ornate 3D Floral Decor” 

separate design to add extra magic to that decoration. 

Egg measures approx. 2.5” horizontal diam. x 3.375” tall. 

ASSEMBLY: 1. Identify and cut the shapes:

A egg slices with vertical center perforation lines (10-12)

B alternative egg slices with top loop for hanging (0-2)

2. Bend each of the egg slices as "valley" folds

and crease, then open again.

3. Position the first two slices back to back so that

the two adjacent halves are back to back

(that is, the right half of left slice is back to back

with the left half of the right slide shown here)

align the cut edges and the perforation lines,

and glue together.

Take care that the perforations of each of the two

slices being joined are stacked precisely along

the perforations, and also that the top and bottom

curved edges also align precisely.

4. Continue to position and attach the adjacent back

halves of the next two eggs until a half egg is completed -

that is 6 slices. If using the alternative egg slices that

include the loop, that special slice should be in 

a specific order in the half egg 6 slice order, such as first.

With the stack folded in half as shown in the previous image,

place under a heavy weight until glue is completely dried.

5. Repeat step 4 to complete the second half,

with the loop shape in the identical order position.

Press until dried.

6. Open the egg stacks and position the beginning and 

end slices next to each other in the same manner

as was accomplished with the beginning assembly.

If using the loop top slices, open so that the loop slice

is "flat" and the remaining slices remain stacked on

one half. 

Position the two halves on top of each other,

and attach the back halves to the adjacent back half

to complete the circuit of slices around into egg form.

Here is the completed egg form. 

7. Spread the slices

so that they are more or less even around the center axis.

One way to assist this is to "fill" the center tunnel

with something, such as this large-gauge needle . . .

. . . which will help the slices even themselves around.

8. If using the loop slices, gently help the front and

back loop extensions to meet up across the center

tunnel, then glue together back to back.

9. If desired, apply glitter to the slice edges.

A) apply a craft "white" style glue to the slice edge;

B) spread some glitter on a work surface with paper "liner"

so excess can be re-collected when finished;

C) roll the slice's edge through the glitter pile 

so that white glue will pick it up;

D) allow to dry somewhat before moving on

to add glue and glitter to each of the edges

in succession.

10. Prepare a cord or wire hanger to thread through

slice form center tunnel.

For the sample project, a 12" or so length of wire "thread"

was folded in half, and the loop (bottom) end

rolled/twisted into a corkscrew "knob".

Wire ends where threaded through tunnel from

bottom end to top, then . . .

. . . at top a hanging loop was twisted in place, and the raw

ends trimmed to appropriate length, and crimped

to remain close to main stems.

Finish with a soft ribbon, tied with knot and bows 

in place at top stem.

Add a decorative hanging hook, if desired.

The completed slice form egg is shown here as

the "dangler" for the Lantern 3D Floral Decor project.