Festive holiday decoration or gift box
composed
of lid and snugly fit base
that slides into the lid backside.
Beard,
hat brim and tassel are made thick
with built-up layers.
Interior of base has a cross piece for
strength and stability.
Add cross-hook strips to pull in lid sides.
Measures approx.
5.25" wide (base) x 8.5" tall.
ASSEMBLY: 1. Identify and cut the shapes:
A LID main shape
B BASE main shape C base cross strut
D Lid main accent triangle
E main beard (top layer)
F main beard under layer
G beard build up (6-7 duplicates)
H face shape I hat brim (top layer)
J hat brim second layer, build up (6-7)
K tassel scalloped circle with top smaller tassel (2)
L tassel build up layers (6)
5. Prepare the BASE cross strut by bending tabs back,
side wall tabs back, as shown.
On the inside, bring the side walls into perpendicular
position, then attach strut side tabs in place
to inside walls of the BASE.
NOTE: The strut is intended to help the BASE
triangle retain its "squared up" triangle shape.
So as the sides are attached, aim for a uniform
triangle with perpendicular walls.
NOTE: If the box will be used as decor display
only, you will need to install some weight in the
bottom of the base to offset the extra weight
of the layered beard and hat trim
(otherwise, it will tip forward).
Clean new metal washers quick glued onto
the bottom wall of the base is one way
to accomplish this.
8. Layer and glue the top two beard shapes together.
In the sample project, the top beard layer
is glitter card.
10. Layer and attach the hat brim bottom layer
shapes in same manner as beard.
11. Layer and attach the top two brim shapes
(top layer here is glitter card) in the same manner.
. . . then position and attach the face shape
above the guide marks, with the bottom
of face exactly even with cut marks.
15. Position and attach the beard assembly
butting up against the bottom of the face shape
and centered side to side.
Position and attach the hat brim shape.
Add cut circle or stud eyes on the face shape.
16. Complete the assembly of the
LID shape as was done with the BASE
shape in step 4.
20. Bend the side tabs back.
Slide the BASE inside the LID,
then center over the latch assembly over the
back, tuck the side tabs between the LID
and BASE, and slide up or down until
the latch is in its "best fit" position.
21. Without un-adjusting the latch position,
spread the LID sides slightly and apply glue
to the outer surface of the latch tab(s) . . .
A LID main shape
B BASE main shape C base cross strut
D Lid main accent triangle
E main beard (top layer)
F main beard under layer
G beard build up (6-7 duplicates)
H face shape I hat brim (top layer)
J hat brim second layer, build up (6-7)
K tassel scalloped circle with top smaller tassel (2)
L tassel build up layers (6)
M & N back latch strips
2. Prepare the LID main shape by bending back
on all perforations, including side tabs
and side rim flanges.
3. Prepare the BASE main shape by folding
back on all perforation lines in similar manner.
4. Complete the side seams by bending side walls
up at adjacent positions, bending tab back,
then bringing straight edge to overlap tab
and with wall straight edge even with perforation
line. Glue in place.
Repeat for the other two side seams of BASE.
Complete the side seams of the LID shape
in similar manner.
side wall tabs back, as shown.
6. Insert the bottom tabs into the corresponding
slots in the back wall.
On the backside, bend the tabs downward.
Apply glue to the underside of tabs,
then attach to the outside face of the BASE.
position, then attach strut side tabs in place
to inside walls of the BASE.
NOTE: The strut is intended to help the BASE
triangle retain its "squared up" triangle shape.
So as the sides are attached, aim for a uniform
triangle with perpendicular walls.
NOTE: If the box will be used as decor display
only, you will need to install some weight in the
bottom of the base to offset the extra weight
of the layered beard and hat trim
(otherwise, it will tip forward).
Clean new metal washers quick glued onto
the bottom wall of the base is one way
to accomplish this.
7. Prepare the "thick" beard shape by layering and
gluing the 6 or 7 bottom layers together,
one by one, aligning all cut edges as accurately
as possible.
HINT: press this assembly - and all build-up
layers - under flat weights during the glue drying
process to help prevent curling or warping.
In the sample project, the top beard layer
is glitter card.
9. Position and attach the beard top layer
onto the bottom build up beard layers.
(This image shows brad heads positioned
at the punch holes - these were omitted
in the final version.)
shapes in same manner as beard.
(top layer here is glitter card) in the same manner.
12. Add brad heads or studs to the brim holes,
then layer the brim upper layers onto the
build up bottom layer assembly and attach.
13. Layer the tassel circles to build up in
a similar manner . . .
. . . and add the smaller top circle to the assembly.
14. Identify the beard position guide marks
on the triangle accent shape . . .
above the guide marks, with the bottom
of face exactly even with cut marks.
butting up against the bottom of the face shape
and centered side to side.
Position and attach the hat brim shape.
Add cut circle or stud eyes on the face shape.
LID shape as was done with the BASE
shape in step 4.
17. Bend the rim flange tabs to the inside
of the LID and glue in place.
18. Position and attach the tassel
circle assembly over the LID tip.
19. Prepare the back latch assembly
by sliding the tip slots together as shown,
and push together until the strip long edges
are parallel.
Slide the BASE inside the LID,
then center over the latch assembly over the
back, tuck the side tabs between the LID
and BASE, and slide up or down until
the latch is in its "best fit" position.
spread the LID sides slightly and apply glue
to the outer surface of the latch tab(s) . . .
. . . then apply pressure to the sides of the
box to attach the latch side tabs to
the inside of LID, and hold in place
until secure.
No comments:
Post a Comment