Christmas 3D Quilt Stand With Quilt Minis

Christmas standhas dimensional ends 

with offset accent overlays (with folk heart flourish), 

arched legs connected with hexagon tubes 

(reinforce with 5/16" dowel lengths), 

this quilt display stand makes a unique 

and beautiful seasonal accent. 

Pair with Christmas Cactus . . .

. . .or Christmas Trees 

quilt minis companion designs (constructed of paper) 

which can be draped over the top pole. 

Or, stitch a fabric mini quilt 

of your own choosing to display. 

Stand measures approx. 7.5" tall x 7.75" wide x 2.75" deep 

(fits other "Quilt Minis" available as cut file downloads). 

The quilt minis are constructed separately

from the 3D stand.

The assembly guide instructions

for these two follow the stand instructions.

QUILT STAND ASSEMBLY:

1. This "new" version of the 3D display stand is

constructed in the same fashion as the "original"

"Quilt 3D Display Stand which can be found

at this post on this blog.

2. SHAPES: cut the same shapes as identified

in the other blog post (A-G, J & K),

noting that A & B will NOT have the heart cutout

in this "Christmas" version, and that K outer accent

will look like the left shapes below, with the

folk art decor motif cut shapes as shown.

Also, the shapes shown below at right are 

inner accent shapes, a shape not used in the original.

3. Follow the original stand assembly steps,

beginning at Step 7 (this omits the heart cutout prep).

Before Step 8, position and attach the 

inner overlay shapes shown above, left,

over the inside panels.

Continue working through Step 12 as described. 

Skip Steps 13, then continue with Step 14

(obviously omitting references to gluing to

heart cutout flanges, etc.), and continue

through Step 23.

4. Before Step 24, prepare the "new"

outer panel overlays by positioning

and attaching the accent shapes as shown in
the following photo.

TIP: One way to assist with the positioning

is to create a positioning guide by keeping

the flourishes, heart and small punch circle

grouped together as they are when the file 

opens up, then arrange

that group as an isolated cutting design on the

cutting mat, and cutting the group out of 

a scrap of card stock as a stencil.

Position the tracing stencil, centered on top

of the accent panel with the designs approx. 7/16"

down from the top straight panel edge,

then make some light guidemarks

with fine, sharp pencil.

(NOTE that this image is simulating

the tracing, even though the accent shapes

are already in position.)

5. Complete Step 25, placing the outer end

accents into position to finish the

display stand.

CHRISTMAS CACTUS QUILT MINI ASSEMBLY:

1. Identify and cut the shapes:

A main quilt panels (front, back)

B top quilt panel (bendy)

C side "binding" narrow border strips (4)

D end "mitered" narrow border strips (2)

E short side narrow borders strips (4)

F top panel end border strips (2)

G "block" base   H "berries" show thru panel

I top block panel   J cactus shape

2. Prepare the main and top quilt panels

by bending back on the perforations:

one near top of main panel; two at top panel edges.

3. Position and attach the narrow side borders

to the side edges of the main quilt panels

(below perforation lines).

4. Position and attach the bottom "miter" border

strip to the end edge, and short side borders

to the upper edges (above perforation lines)

5. Position and attach the top panel short strips

to the side edges between perforation lines.

6. Overlap one main panel top edge over the

punch hole edge of the top panel, taking care

to align side edges and punch holes,

and glue in place.

7. Prepare to complete the lacing of the main

and top panels by cutting a 20" length of perle cotton,

soft twine, or 6-ply floss and thread onto the

smallest tapestry-style needle that will fit the

"thread" you are using. Tape one end to backside

of main panel near one end of the row of punch holes.

8. Insert needle into the end hole, from back to front . . .

. . . push to the front, and pull all the way through.

Complete the first stitch by inserting the needle

down into the second hole and pull

all the way through.

Continue to complete the stitches in the same

manner all the way across the row . . .

. . . to the final stitch, inserting the needle through

to the backside.

9. "Park" the needle away to one side, then

overlap and attach the second main panel

as shown in Step 6.

10. Prepare to complete the second row of

stitches by passing the needle across the back

of the top panel to insert in the first hole,

then continue the stitching process across

the complete length of the second row,

with the final stitch bringing the needle and

"thread" to the backside of the assembly.

11. Cut a tail of approx. 1" . . .

. . . and anchor the end with a small piece of tape

like the anchor to attach at the beginning.

Also attach the crossing stitch between the

two rows, to keep it in place while on the stand.

12. Assemble the cactus by layering and attaching

the top block layer over the berry "show-thru" layer,

then position and attach the cactus shape

centered on the diagonal.

Position and attach the cactus assembly centered

on the main block panel.

13. Position and attach the block on the front

of the main quilt panel.

14. Place the quilt mini over the stand top pole

so that the top panel is "balancing" there,

with the front and back panels hanging downward.

Here is the completed cactus quilt mini on the stand.

TRIANGLE TREES QUILT MINI

1. Identify and cut the shapes:

A inner frame border  B main assembly panel

C tree base "blocks" (4)  D tree shape (4)

E inner triangle shape (4)

F trunk rectangles (4)

G optional 5x5 card base (to convert

the cactus or triangle tree block into a card front)

2. Position and attach the narrow frame on
the assembly base, taking care to align all
outer edges as precisely as possible.

3. Position each tree at the center of its block

with base edge aligned at bottom edge,

and attach in place.

4. Position and attach the trunk rectangle over

the corresponding portion of the tree shape.

5. Position the inner triangle shape over the center

of the tree shape so that the bottom point is

centered and touches the trunk shape.

Complete four tree blocks.

6. Place the first block snugly into the corner

inside the narrow frame, and attach in place.

Position and attach the remaining three blocks

into the other positions within frame, taking care

to snug them into each corner and next to

adjacent blocks.

6. Position and attach the triangle trees block

onto the front main panel, in the same manner

as the cactus block was attached in Step 13

of that quilt mini assembly.

Or, prepare the card base then position

and attach the triangle trees "block" or the

cactus "block" onto the front of the card.